1. Tsari Tsari
1.1 Ana ba da shawarar yin amfani da tsarin ƙirƙira rufaffiyar mutuƙar tsaye don tabbatar da ingantaccen rarraba tare da sifar waje na jabun ɓangaren.
1.2 A general tsari kwarara hada da abu yankan, nauyi rarraba, harbi ayukan iska mai ƙarfi, pre-lubrication, dumama, ƙirƙira, zafi magani, surface tsaftacewa, Magnetic barbashi dubawa, da dai sauransu
1.3 Yin ƙirƙira tasha ɗaya ya fi dacewa don ƙirƙira. 1.4 Kayayyakin ya kamata a zabar daga karfe 45 #, 20CrMo, karfe 42CrMo, da sauran makamantan su.
1.5 Yana da kyau a yi amfani da injin sawing don yankan kayan don cire ɓangaren kai da wutsiya.
1.6 Hannun bawon sanda mai zafi da aka yi birgima an fi so.
1.7 Don tabbatar da samfurin ya cika da haɓaka rayuwar mutuƙar, ana ba da shawarar yin amfani da na'urori masu ɗaukar nauyi masu yawa don rarraba abubuwan da ba su da lahani ta inganci.
1.8 Abubuwan da ba su da lahani ya kamata a yi gwajin fashewar fashewar. Zaɓin kayan aikin fashewar harbi, kamar diamita masu dacewa na harbe-harbe (a kusa da Φ1.0mm zuwa Φ1.5mm), yakamata yayi la'akari da abubuwa kamar buƙatun saman buƙatun buƙatun, adadin harbe-harbe kowane zagaye, lokacin fashewar harbi, da tsawon rayuwar harbi.
1.9 The preheating zafin jiki ga m kayan ya kamata a cikin 120 ℃ zuwa 180 ℃.
1.10 Pre-shafi graphite taro ya kamata a ƙaddara dangane da graphite irin, surface ingancin forgings, dumama zafin jiki, da kuma duration.
1.11 Graphite yakamata a fesa daidai gwargwado a saman kayan da ba su da lahani ba tare da tari ba.
1.12 Graphite ya kamata ya iya jure yanayin zafi a kusa da 1000 ℃ ± 40 ℃.
1.13 Matsakaici-mita shigar da tanderun dumama ana ba da shawarar don kayan dumama.
1.14 Za a iya ƙayyade lokacin dumama don kayan da ba su da lahani bisa ga kayan dumama, girman billet, da saurin samarwa, da nufin cimma daidaiton zafin jiki na ƙirƙira.
1.15 Zaɓin zafin jiki na dumama don kayan da ba su da lahani ya kamata su ba da gudummawa don haɓaka haɓakar kayan abu da samun kyakkyawan tsarin ƙirƙira da ingancin ƙasa.
- Ƙirƙira
2.1 Zaɓin filaye don ƙirƙira ya kamata ya sauƙaƙe cire ƙura, cika ƙarfe a cikin rami, da sarrafa ƙura.
2.2 Ya kamata a yi amfani da nazarin simintin ƙididdiga na lamba don ƙididdige ƙarfin lalacewa da kuma toshe ƙarfi yayin aikin ƙirƙira.
2.3 The preheating zafin jiki kewayon ga molds ne kullum tsakanin 120 ℃ da 250 ℃, tare da m preheating lokaci na 30 minutes. A mold zafin jiki kada ya wuce 400 ℃ a lokacin samar tsari.
Lokacin aikawa: Nuwamba-13-2023
